![]() ![]() There seems to be nothing wrong with the drives, the firmware is up to date, no errors in the ADU or Insight Diagnostics. I have a Proliant D元80 G3 and during a routine walkthrough of the server room I noticed two hard drives with blinking amber lights. As Robert has said, install the software, check your array status and make sure your backups are complete before you pull the drive. Its possible, but unlikely that the disk is in a non-swappable array. Say it's the onboard controller, slot=0.Ĭtrl slot=0 ld 1 add drives=allunassignedįrom there, you can modify the logical drive to change its redundancy level (although this may be automatic in this specific case). Amber light on hard drive will not stop blinking. Go to the 'view disks - logical view' to see how theyre configured. Mine has been running for about 2 weeks now without 1 above. 1) the M元50 G6 powers off for no know reason and does not restart (in these cases there is no apparent loss of AC power), and 2) the M元50 G6 does not stay powered-on during power outage even when on UPS of significant size. Grab the controller slot number and logical drive ID. Threads are present on both about the problems I am having. Going from RAID 0 to RAID 1 really only gives the option of adding a disk and changing the logical drive's redundancy level.Įnter hpacucli and run ctrl all show config ![]() Add the new disk(s) to the existing logical drive, then optionally expand the logical drive. If power is off, view status on the rear panel RJ-45 LEDs ('Rear panel LEDs and buttons' on page 10). You're basically going to run this in two steps. 3 Power cap LED Green Power cap configured Flashing amber Power cap exceeded Off Server in standby or power cap disabled 4 NIC 1 activity LED Green Network link Flashing Network link and activity Off No link to network. But if that's not available, the hpacucli command-line utility will work as well. ![]() I prefer doing expansions via the graphical HP Online Array Configuration utility enabled by ( cpqacuxe -R and browsing to ) if you have the full set of HP Management Agents installed. All LEDs in the motherboard are off except for: - PPM2: blinking in amber. So, I noticed my motherboard LEDs and referred to System board LEDs section. and for the external health LED: Red Critical power supply failure. You may even have a blinking amber light on the drive, versus the solid amber indicating failure. To identify the component in a critical state, refer to system board LEDs. Power on Flashing green Waiting for power due to group power capping Amber System in. The disk described in the original problem is a drive pre-failure (either from S.M.A.R.T. HP ProLiant M元50 G6 Manual Online: Front Panel Leds And Buttons. It is a bit of work to get setup, but well worth it.I'm not sure if you've completed this yet, but this is definitely possible, assuming your Smart Array controller has a battery or flash-back cache unit (needed for all RAID-level tranformations/expansions). From there, you will want to check out the alerts in ilo. You can also set a username and password using the online configuration tool above. If it has never been configured, the username will be administrator and the password is on the service tag on the machine (either a pullout tab somewhere or just a label). The tool can be found here:įrom there, you will log into the ilo. From there, you can use HPs online ilo configuration utility to check if it has an IP (and configure one if not). The two NICs right next to each other will be your network while the one right next to the USB ports is ilo. It should have three onboard NICs (ignore the PCI card NICs if any). Ilo should be configured, but there is a chance it is not connected to the network. I have this same server (specifically an M元50e, but there is also M元50p). ![]()
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |